366 items in Australia for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
1
Wanted Hilborn fuel injection for 4 cylinder engine, prefer to suit Nissan L Series motor, but can adapt, regards AJ
10
Lotus 7/ Clubman chassis. This car was raced by my father in the 70s and has been in storage since. Believed to be a Lotus 7 but cannot verify this, the only stamp I can find on the chassis is shown in the photos. Definitely not complete but includes many parts as pictured. Happy to answer any questions or arrange more photos if required.
3
AP Racing CP6465-218 pull type master cylinder 21.8mm
4
3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17 NOTE WHEEL ARE FOR VR VS COMMODORE
13 1
Roll CageLog Book
Toyota Supra drag car, full chassis complete ready to race. 410 cube SBC running methanol ,all engine specs can be supplied , new Ray Edwards carburetor, hughes powerglide with convertor to suit, 9 inch 35 spline floating axle with 1/4 & 1/8th mile gear sets, new front runners and slicks, car runs straight and consistent with engine and trans assembly only doing 12 passes, Andra tech and paper work available
17
Lucas Fuel Injection off Lotus Twin Cam 6mm Metering unit, High pressure electric pump with filter. belt driven low pressure pump metering unit with drive throttle bodies slides in very good condition. Has been in storage for a number of years, I would recommend new lines and a check through before using. Can be freighted Australia wide or International must be with insurance .
3
Sydney Composites front splitter, used at WTAC in 2023 would suit either open class or Pro-Am, 2200mm wide and 810mm wide but can be reduced if required. Proven to produce massive down force with low drag. Titanium Wear Plates. Only selling due to changing direction. Happy to answer questions 0427700423 and can freight Austria wide
6
AP Single plate , plate is 10 7/8 spline presents as new measures 2.63 mm . Can post Australia wide
2
This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.
9
RegisteredRoll Cage
Thank you for looking at this lovely & very rare example of the Westfield Seight available here in QLD fully road registered with RWC and fresh from a detailed and thorough re- commission, showing just 21k kms in its 25 year life with matching numbers and original VIN. Why am I selling? – because I just couldn’t resist the opportunity to buy it, BUT have at least one too many projects on the go so after countless daily hours of work, shakedown and detailed attention it’s time for it to move on t
5
A Carbon Fiber rear three element wing for Hillclimb Time Attack cars. This wing has never been fitted to a car and is as new. I imported the wing from the UK at a cost of 5000GBP. The elements have hard points engineered into the structure for mounting and support. Main Element Length is 1720mm and cord is 300mm. Second element is 1720mm x 120mm and third element is 1720mm x 115mm. Each element can be adjusted or removed.
7
Hollinger 6 speed H Pattern gearbox with Chevy bell housing and input shaft and shifter included. It has receipts for overs $9,000 in reconditioned repairs to bring it up to Like new condition. These gearboxes are very rare, so jump the order queue and grab this one now
1
Brand new Albins ST6 6 speed with paddle shift. Front bell housing for clutch. Same as Marc car setup.
6
NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.
3
I have 19 available $40 each which is less the half price can post Australia wide
2
Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20
14
Roll Cage
Chevrolet camaro 1968 drag car tabbed 15 inch wide wheels Dana diff front fiberglass clip imported from states. . Cage so much work in car left hand drive set up for big block Chevrolet twin turbo also have pipes made for twin gt42s
8
Sr20de fully rebuilt. Custom made pistons for 14:1 compression, h beam rods, big crow cams, golbys adjustable cam gears, gtir intake manifold. Block was cleaned, decked and machined. Crank shaft was machined and balanced. Light weigh under drive harmonic balancer. Head was cleaned tested machined and ported. Comes with brand new clutch kit with a light flywheel. Engine is ready to bolt in and run.
13
Our Latest Generation Load Cell Simulator Kit for PE Racing Billet Pedal Assembly Designed & developed to feel realistic, and handle real life pedal forces. PE Racing Load Cell Sim Racing Kit is designed for professional Motorsport Simulators & gaming. Designed to suit the Patented PE Racing Billet Pedal Box. Driving Simulators typically see more laps than real race cars, and thus these sim cylinders must withstand the same forces with increased cyclic loads. We have designed & developed thes
6
Type 9 Quaife Close Ratio Straight Cut Gearbox. Suit clubman of modified Escort. Never fitted to the car, went for a sequential 5 speed. All new bearings/gaskets and seals I think the Ratio: 2.2/1.69/1.21/1:1/0.873500