215 items under $10,000 for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
4
3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17
17
Lucas Fuel Injection off Lotus Twin Cam 6mm Metering unit, High pressure electric pump with filter. belt driven low pressure pump metering unit with drive throttle bodies slides in very good condition. Has been in storage for a number of years, I would recommend new lines and a check through before using. Can be freighted Australia wide or International must be with insurance .
3
Sydney Composites front splitter, used at WTAC in 2023 would suit either open class or Pro-Am, 2200mm wide and 810mm wide but can be reduced if required. Proven to produce massive down force with low drag. Titanium Wear Plates. Only selling due to changing direction. Happy to answer questions 0427700423 and can freight Austria wide
6
AP Single plate , plate is 10 7/8 spline presents as new measures 2.63 mm . Can post Australia wide
16
RegisteredLog Book
A very quick car that goes really really well, and sounds glorious - the 3.0i Busso V6 is known to be one of the all time great engines. If I was keeping it I would put a set of 17" teledials on it. ( I have a set of 16" teledials, so they will go with the car, just needs spacers (supplied) to clear the Brembos - Only selling as I have a race project on the go (yes, it's an Alfa......) But that's what ALFA stands for isn't it ? Always Looking For Another....... I have three at the moment, so I
2
Near New M800 and Data Logger Dash has not been used I owned as a spare for my FD RX7 Racecar. features enabled are as follows: M800 SN1323 single lambda, Hi/lo injection, Cam control, Advance functions (Traction control, Launch Control, Gear Ign cut, Overun boost) Dash ADL Dash SN 2732 shift / warning lights 1mb logging, Pro logging, standard inputs, See attached screen shot
2
This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.
5
A Carbon Fiber rear three element wing for Hillclimb Time Attack cars. This wing has never been fitted to a car and is as new. I imported the wing from the UK at a cost of 5000GBP. The elements have hard points engineered into the structure for mounting and support. Main Element Length is 1720mm and cord is 300mm. Second element is 1720mm x 120mm and third element is 1720mm x 115mm. Each element can be adjusted or removed.
6
NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.
3
I have 19 available $40 each which is less the half price can post Australia wide
2
Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20
32
Roll Cage
Daihatsu Charade 1986 G11 Turbo originally a turbo car ! CB80 T conversion - twin cam fresh rebuild inc. forged Pistons - new water pump - belt and gaskets Good paint - exterior Half Cage fuel cell in boot willwood brake conversion _ not complete spare near complete engine spare - donor car Will need completing sold as project - unfinished project car REQUIRES wiring - either standard ECU (supplied) haltech and loom $2000 extra brakes - need plumbing and finishing off turbo - eith
8
Sr20de fully rebuilt. Custom made pistons for 14:1 compression, h beam rods, big crow cams, golbys adjustable cam gears, gtir intake manifold. Block was cleaned, decked and machined. Crank shaft was machined and balanced. Light weigh under drive harmonic balancer. Head was cleaned tested machined and ported. Comes with brand new clutch kit with a light flywheel. Engine is ready to bolt in and run.
10
Registered
2001 gen7 zzt231 celica 6 speed, Trd , rotrex supercharger,front mount intercooler etc. Has engineering cert in tasmania. Looking for a new project ?( i have another project taking my time and energy for now)This car has a blown motor after throwing a rod.Needs new block, 1 x mahl piston and rod,machining.The head/valves and crank seem ok.The motor/ supercharger had 50k on it after complete rebuild.(motor was over revved )after clutch problem. As far as power it was running 275kw atw @ 7psi o
13
Our Latest Generation Load Cell Simulator Kit for PE Racing Billet Pedal Assembly Designed & developed to feel realistic, and handle real life pedal forces. PE Racing Load Cell Sim Racing Kit is designed for professional Motorsport Simulators & gaming. Designed to suit the Patented PE Racing Billet Pedal Box. Driving Simulators typically see more laps than real race cars, and thus these sim cylinders must withstand the same forces with increased cyclic loads. We have designed & developed thes
6
Type 9 Quaife Close Ratio Straight Cut Gearbox. Suit clubman of modified Escort. Never fitted to the car, went for a sequential 5 speed. All new bearings/gaskets and seals I think the Ratio: 2.2/1.69/1.21/1:1/0.873500
3
In very good condition located in Adelaide ideal for single seater period correct 50’s to 60’s or 70’s car.
11
Pedal Sliders Designed & Manufactured in Australia by PE Racing These are specifically designed to suit our PE Racing Pedal Assemblies and cater for the FIA fixed seat regulations. A little about our Pedal Assembly. This PE Racing Patented Frame design came about as a result of common problems experienced while installing pedal assemblies to a range of race cars over many years. Initially a typical floor mount frame usually has a relatively short flat footprint, the brake pedal forces ultima
10
Load Spreading Washers - with 12mm locating shoulder to underside. How often do you find the panels you mount end up with the holes flogged out? Simple but effective, we designed this washer with a locating shoulder on the underside. This provides better lateral support for the connection. It reduces the bearing load by increasing the connection hole surface area. This results in less movement & reduced wear. Manufactured of Aircraft alloy in a range of sizes to suit M5, M6 & M8 counters
4
Complete set of original Porsche 997.2 S4 wheels and tires approx. 40% worn As new with no scrapes or blemishes. Fronts 19X8 235X35X19 Perilli "P" Zero Rears 19X11 305X30X19 Perilli "P" Zero