234 items under $10,000 for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
10
Lotus 7/ Clubman chassis. This car was raced by my father in the 70s and has been in storage since. Believed to be a Lotus 7 but cannot verify this, the only stamp I can find on the chassis is shown in the photos. Definitely not complete but includes many parts as pictured. Happy to answer any questions or arrange more photos if required.
3
AP Racing CP6465-218 pull type master cylinder 21.8mm
4
3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17 NOTE WHEEL ARE FOR VR VS COMMODORE
2
In perfect condition excluding the large daggy seat, hydraulic brakes, tach/hour meter, balanced for a 85 kg driver so she goes really well in the corners around the back yard, an impulse buy new which ignored my age. So she has had little use, original tyres, your chance to grab a bargain and rip off a boomer at the same time. Phone will likely go to message, email rzgreenup@gmail.com
5
Engineer built for personal use.Single axle, torsion suspension,NO RAMPS, hand winch,DRIVE ON/DRIVE OFF or winch.1640(5'4") wide 3300 (10"10"")long (rails).Width is adjustable IN.Ratchet straps at front.ELECTRIC BRAKES/Hand brake .14x6 Sunraysia wheels/185-LT tyres(90%).One person operation,Will not disappoint.NSW Reg X22090 expires April25.
3
Sydney Composites front splitter, used at WTAC in 2023 would suit either open class or Pro-Am, 2200mm wide and 810mm wide but can be reduced if required. Proven to produce massive down force with low drag. Titanium Wear Plates. Only selling due to changing direction. Happy to answer questions 0427700423 and can freight Austria wide
16
RegisteredLog Book
A very quick car that goes really really well, and sounds glorious - the 3.0i Busso V6 is known to be one of the all time great engines. If I was keeping it I would put a set of 17" teledials on it. ( I have a set of 16" teledials, so they will go with the car, just needs spacers (supplied) to clear the Brembos - Only selling as I have a race project on the go (yes, it's an Alfa......) But that's what ALFA stands for isn't it ? Always Looking For Another....... I have three at the moment, so I
8
Registered
2008 Smart Fortwo Motorkhana Khanacross Perfect car to get involved in motorkhana and khanacross. This car was bought for my then 12 year old daughter to kick off her motorsport adventures and she is now moving up to car more suitable for the 2025 NSW Supersprint series. Used for the NSW state motorkhana series - we came 2nd/3rd in Class A in 2023. Clever features include a drivers seat that goes up in height as it slides forward to accommodate smaller drivers (like my then short for her siz
2
Near New M800 and Data Logger Dash has not been used I owned as a spare for my FD RX7 Racecar. features enabled are as follows: M800 SN1323 single lambda, Hi/lo injection, Cam control, Advance functions (Traction control, Launch Control, Gear Ign cut, Overun boost) Dash ADL Dash SN 2732 shift / warning lights 1mb logging, Pro logging, standard inputs, See attached screen shot
2
This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.
6
Ideal start for your track project. The BMW is in very good condition rust and damage free. It needs an engine rebuild with suspected rod bearing damage. Rebuild it or engine swap. Car is in Newcastle and whilst it runs it will need to be towed.
6
NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.
3
I have 19 available $40 each which is less the half price can post Australia wide
2
Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20
8
Roll CageLog Book
Astra CDTi production car, Holden factory race car built by PMM for the 2007 Bathurst 12 hour sponsored by Bendon, built to showcase the power of the new diesel Astra. Also competed in the 2009 12 hour for the Holdsworth family, did some production racing for a few years after but more recently just used as a fun track car. Very well built, 6 speed, DMS suspension, Racetech seat, Performance Box with power and external antenna, we use ex Toyota 86 semi slicks for very cheap fun. Would need harne
8
Sr20de fully rebuilt. Custom made pistons for 14:1 compression, h beam rods, big crow cams, golbys adjustable cam gears, gtir intake manifold. Block was cleaned, decked and machined. Crank shaft was machined and balanced. Light weigh under drive harmonic balancer. Head was cleaned tested machined and ported. Comes with brand new clutch kit with a light flywheel. Engine is ready to bolt in and run.
8
2012 tandem race car trailer Beaver tail Hidden pull out ramps Electric winch Will come with a new battery Breakaway system Deck is 14ft Total length of trailer and draw bar is 20ft Inside the guards are 1,900mm The total width of the trailer is 8ft Registration until November
5
This car trailer is in near-new condition. Built in October 2021. Used to carry race car. 4.83m long and 2.0m wide at the tray. Wider and longer than usual. Has been stored inside my warehouse when not in use, never outdoors. Has extra shackle loops, manual winch and long ramps. Licensed and ready to use.
13
Our Latest Generation Load Cell Simulator Kit for PE Racing Billet Pedal Assembly Designed & developed to feel realistic, and handle real life pedal forces. PE Racing Load Cell Sim Racing Kit is designed for professional Motorsport Simulators & gaming. Designed to suit the Patented PE Racing Billet Pedal Box. Driving Simulators typically see more laps than real race cars, and thus these sim cylinders must withstand the same forces with increased cyclic loads. We have designed & developed thes
6
Type 9 Quaife Close Ratio Straight Cut Gearbox. Suit clubman of modified Escort. Never fitted to the car, went for a sequential 5 speed. All new bearings/gaskets and seals I think the Ratio: 2.2/1.69/1.21/1:1/0.873500